This OEG buffer storage tank fulfills the highest demands on heat storage, particularly where those heat generators are used which achieve their optimal efficiency only under full load...
All product informationRelated products
10-year warranty
High Quality
TÜV Rheinland
This OEG buffer storage tank fulfills the highest demands on heat storage, particularly where those heat generators are used which achieve their optimal efficiency only under full load. (e.g. many solid fuel boilers). During the operation of the heat generator, more heat is produced than the consumers take. The excess heat heats the water of the buffer tank and is therefore stored. During stand-still periods this heat can be later retrieved, as needed. The OEG buffer storage tank is suitable as a primary cylinder for solar systems, heat pumps, wood- or pellet boilers and can also be used in district heating systems. Due to the two additional smooth-pipe heat exchangers, more heat generators can be integrated and their energy can be fed into the buffer tank additionally.
For more information see Downloads
| OEG no. | 516008070 |
| Installation type: | Vertical storage tank |
| Manufacturer | OEG |
| Notes |
10-year warranty
High Quality
TÜV Rheinland
|
| Customs tariff number | 73090059 |
General
| Rated volume according to EN 12897: | 1000 |
| Colour: | blue |
| Insulation according to DIN 4102-1 Fire Protection Class B2: | removable segment insulation |
| Weight [kg]: | 333 |
| Total height including insulation [mm]: | 2350 |
| Diameter without insulation [mm]: | 790 |
| Diameter with insulation [mm]: | 1015 |
| Tilt height [mm]: | 2280 |
| Heat retaining loss according to EN 12897 [W]: | 55 |
| Heat losses in stand-by mode according to DIN 12897 [kW/h / 24 h]: | 1,320 |
| Real volume according to EN 12897 [l]: | 988 |
| pmax Tank [bar]: | 3 |
| tmax Tank [°C]: | 95 |
| tmin Tank [°C]: | 20 |
| Smooth-pipe heat exchanger [number]: | 2 |
| Smooth-pipe heat exchanger area bottom [m²]: | 3,30 |
| Smooth-pipe heat exchanger area top [m²]: | 2,60 |
| Smooth-pipe heat exchanger volume bottom: | 21,30 |
| Smooth-pipe heat exchanger volume top: | 17 |
| pmax Smooth-pipe heat exchanger [bar]: | 10 |
| tmax Smooth-pipe heat exchanger [°C]: | 130 |
| Connection layout: | 90° |
| Connection sensor [Ø mm / terminal]: | 6 mm |
| Connection heat generator [thread]: | Rp 1 1/2" |
| Connection heat exchanger [thread]: | Rp 1" |
| Connection heating element [thread]: | Rp 1 1/2" |
| Max. immersion depth of screw-in heater [mm]: | 800 |
Bonjour Pouvez-vous me confirmer que ce ballon peut être adapté avec une résistance électrique à bride de10 kw (400 V) ? merci
Bonjour,
Il faut donc généralement faire attention à ce que la résistance électrique souhaitée a comme profondeur d'immersion. L'élément chauffant, que l'on pousse dans le ballon, doit bien sûr être placé de manière à pouvoir être fixé ou vissé.
La référence Screw-in heater 4.5 kW par exemple a une profondeur d'immersion de 500 mm. Vous devez prévoir une zone non chauffée de 150 mm, qui se trouve directement derrière le raccord fileté/à bride sur le ballon. Pour des raisons d'efficacité, la résistance électrique doit également s'arrêter à peu près au milieu du ballon et ne doit pas traverser l'autre côté.
is mantel los leverbaar
De isolatiemantel is los verkrijgbaar, maar betreft geen voorraad artikel.
Indien gewenst kunnen wij de mantel voor u bestellen.
Zodra wij een prijs en levertijd doorkrijgen van de betreffende isolatie zullen wij u dan een offerte sturen.